Teltonika Switches

The Teltonika TSW101 is an automotive unmanaged Ethernet switch built for in-vehicle networking, providing five Gigabit Ethernet ports with four supporting PoE+ for simultaneously connecting and powering compatible devices. It accepts a 9-30 VDC input, allowing direct connection to common 12 V and 24 V vehicle power systems without requiring an additional power supply. Its compact aluminium housing, wide operating temperature range and flexible mounting options make it suitable for vehicle-based connectivity installations.

Key Features of Teltonika TSW101 Five Gigabit Ethernet ports supporting 10/100/1000 Mbps
Four PoE+ ports with IEEE 802.3af and IEEE 802.3at support
Up to 30 W PoE power per port
60 W total PoE power budget at PSE
9-30 VDC input for 12 V and 24 V vehicle power systems
Plug-and-play unmanaged operation
10 Gbps non-blocking bandwidth
128 KB packet buffer and 2K MAC address table
Jumbo frame support up to 9216 bytes
Automotive Gigabit Connectivity Five 10/100/1000 Mbps Ethernet ports provide Gigabit network connectivity for in-vehicle equipment. Four ports support PoE+, while the fifth port can be used as an uplink for connecting the switch to a router, modem or wider network.

PoE+ Power Delivery Four Ethernet ports support IEEE 802.3af and IEEE 802.3at PoE standards, allowing compatible devices to receive network connectivity and electrical power through a single Ethernet connection. Each PoE port can provide up to 30 W, with a total PoE power budget of 60 W at the power sourcing equipment.

Plug-and-Play Operation As an unmanaged switch, the unit operates without requiring network configuration. Auto MDI/MDIX support provides automatic cable crossover detection, while the 10 Gbps non-blocking bandwidth, 128 KB packet buffer and 2K MAC address table support everyday Gigabit Ethernet switching requirements.

The Teltonika TSW100 is an industrial unmanaged Gigabit Ethernet switch with four PoE+ ports and one dedicated uplink port. It supports IEEE 802.3af and 802.3at PoE standards, delivering up to 30 W per PoE port with a total PSE power budget of up to 120 W. Five 10/100/1000 Mbps Ethernet ports provide high-speed wired connectivity, while DIN rail and surface mounting options allow flexible installation in industrial environments.

Key Features of Teltonika TSW100 5 x Gigabit Ethernet ports
4 x PoE+ ports and 1 x uplink port
IEEE 802.3af and 802.3at PoE support
Up to 30 W PoE power per port
Up to 120 W total PoE power budget at PSE
10/100/1000 Mbps Ethernet speeds
10 Gbps non-blocking bandwidth
128 KB packet buffer
2K MAC address table
9216-byte jumbo frame support
Automatic MDI/MDI-X cable detection
DIN rail and surface mounting options
Gigabit Ethernet Connectivity The switch provides five RJ45 Ethernet ports supporting 10/100/1000 Mbps connections. Four ports provide PoE+ output, while the remaining port serves as an uplink for connecting the switch to a wider network.

PoE+ Power Delivery Four Ethernet ports support IEEE 802.3af and 802.3at PoE standards, allowing compatible devices to receive both network data and electrical power through a single Ethernet cable. Each PoE port can provide up to 30 W, with a total PSE power budget of up to 120 W.

Industrial Power Input A four-pin industrial DC power socket accepts an input range of 7-57 VDC. PoE output requires an input voltage between 44 VDC and 57 VDC, while lower input voltages allow the unit to operate as a standard Ethernet switch without PoE output.

Switching Performance The switch provides 10 Gbps of non-blocking bandwidth, a 128 KB packet buffer and a 2K-entry MAC address table. Jumbo frames up to 9216 bytes are supported, while automatic MDI/MDI-X detection simplifies Ethernet cable connections.

Unmanaged Operation As an unmanaged switch, the unit operates without a software management interface or configuration process. Switching and PoE functions are handled by the integrated hardware, allowing connected Ethernet devices to communicate without additional switch configuration.

The TSW010 Ethernet switch provides an economical solution to expand your network by connecting multiple Ethernet devices effortlessly. Equipped with five 10/100 Mbps ports, it guarantees stable and reliable connections ideal for most industrial environments where ultra-high throughput is not essential.

Key Features: Five 10/100 Mbps Ethernet ports for multiple device connections
Reliable and stable network performance
Cost-effective solution for extending network reach
Designed for industrial use where high throughput is not critical
Reliable Connectivity Ensures steady data transfer across connected devices with minimal interruptions.

Industrial Suitability Meets the requirements of most industrial networking applications without unnecessary complexity.

Easy Installation Compact design and plug-and-play functionality for quick setup in any network environment.

Teltonika TSW110 L2 Unmanaged x5 Port Switch


TSW110 is a layer 2 unmanaged switch, which is a simplified version of our earlier product – TSW100.

Possible to power up through the first LAN port.

It has five 10/100/1000 Mbps Ethernet ports for an economical high-bandwidth solution.

It offers a wide range of supported power supply voltages (9-30 V).

Ideal for professional high bandwidth applications to provide reliable data connection.




Front View:

 





Back View:

 






Plug-n-play No additional configuration needed




Mounting DIN rail and surface mounting options




9-30 V Wide range of supported power supply voltages




Durability Rugged aluminium housing




Status LEDs 1 x Power, 10 x Ethernet




Gigabit ETH 5 x Gigabit Ethernet with speeds up to 1000 Mbps




Quick start guide:



Ethernet LAN 5 x LAN ports, 10/100/1000 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIX crossover Performance specifications Bandwidth (Non-blocking) 10 Gbps Packet buffer 128 KB MAC address table size 2K entries Connector 4 pin industrial DC power socket Input voltage range 9 - 30 VDC, reverse polarity protection, voltage surge/transient protection PoE (passive) Passive PoE. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards Power consumption (idle/max) < 0.4 W/ <1.8 W Physical interfaces (ports, LEDs) Ethernet 5 x RJ45 ports, 10/100/1000 Mbps Status LEDs 1 x Power LED, 10 x LAN status LED’s Power 1 x 4 pin DC connector Ground 1 x Grounding screw Physical specification Casing material Full aluminum housing Dimensions (W x H x D) 100 x 30 x 85 mm Weight 227 g Mounting options DIN rail or wall mounting (additional kit needed), flat surface placement Operating environment Operating temperature -40 C to 75 C Operating humidity 10 % to 90 % non-condensing Hardware Ethernet 5 x LAN ports 10/100/1000 Mbps Power supply 9 - 30 V, 4 pin DC connector Power consumption idle: < 0.4 W, max: < 1.8 W PoE input (passive) Passive PoE over 4,5 (power) and 7,8 (ground) pins. Possibility to power up through first LAN port, not compatible with IEEE802.3af and 802.3at standards Connectors 1 x 4 pin DC, 5 x Ethernet Status LEDs 1 x Power, 10 x Ethernet Ingress protection rating IP30 Operating temperature -40 °C to 75 °C Housing Aluminium housing with wall or DIN rail mounting option and grounding capability Dimensions 100 x 30 x 85 mm Weight 227 g Installation Desktop, wall or DIN Rail mountable (additional kit needed) Full specification and details can be found in the Product Datasheet PDF file

A quick start guide can be found in the Quick Start Guide PDF file

A product flyer can be found in the Product Flyer PDF file

The Teltonika TSW200 is an unmanaged industrial PoE+ Ethernet switch providing eight Gigabit Ethernet ports alongside two SFP ports for fibre-optic connections over longer distances. All eight Ethernet ports support IEEE 802.3af and IEEE 802.3at PoE standards, delivering up to 30 W per port with a total PSE power budget of 240 W. Its wide 7-57 VDC input range, aluminium housing and operating temperature range of -40 °C to +75 °C make it suitable for demanding network installations.

Key Features of Teltonika TSW200 8 x Gigabit Ethernet ports supporting 10/100/1000 Mbps
8 x PoE+ ports supporting IEEE 802.3af and IEEE 802.3at
Up to 30 W PoE power per port
240 W total PoE power budget at PSE
2 x SFP ports for fibre-optic connectivity
20 Gbps non-blocking bandwidth
128 KB packet buffer
2K MAC address table
Jumbo frame support up to 9216 bytes
Gigabit Ethernet Connectivity Eight RJ45 Ethernet ports provide 10/100/1000 Mbps network connectivity for compatible equipment. Auto MDI/MDIX crossover support simplifies cable connections, while the unmanaged configuration allows the switch to operate without requiring network configuration.

PoE+ Power Distribution All eight Ethernet ports support IEEE 802.3af and IEEE 802.3at PoE+ standards, allowing compatible network devices to receive data and power through the same Ethernet connection. Each port can provide up to 30 W at the PSE, with a total available PoE budget of 240 W.

Fibre-Optic Uplinks Two SFP ports provide fibre-optic connectivity for extending network links beyond the typical reach of copper Ethernet cabling. The SFP interfaces can be used for connections between switches or other compatible networking equipment using suitable optical modules.

High-Speed Switching Performance A 20 Gbps non-blocking bandwidth capacity supports simultaneous traffic across the Gigabit Ethernet interfaces. The switch also provides a 128 KB packet buffer, a 2K MAC address table and jumbo frame support for frames up to 9216 bytes.

Flexible Power Input The 7-57 VDC input range accommodates a variety of power sources. PoE operation requires an input voltage of 44 VDC or higher, while the switch can continue operating as a standard Ethernet switch when supplied with lower voltages within its supported input range.

The Teltonika SWM280 is a managed L2+ network switch that combines 24 Gigabit Ethernet ports with 4 SFP interfaces for copper and fibre connectivity. It provides 12 PoE+ ports capable of delivering up to 30 W per port, with a total PoE power budget of 300 W, while its routing, VLAN, QoS and network management features provide extensive control over connected devices and traffic.

Key Features of Teltonika SWM280 24 x Gigabit Ethernet ports supporting 10/100/1000 Mbps
12 x PoE+ ports with up to 30 W per port
300 W total PoE power budget
4 x SFP ports for fibre connectivity
L2+ switching with Layer 3 networking features
Static IPv4 and IPv6 routing
Dynamic routing with BGP, OSPF v2, RIP v1/v2 and EIGRP
VLAN, STP, RSTP and loop protection
PROFINET, EtherNet/IP and MRP support
SNMP v2 and v3 network management
Rack-mountable 1U form factor
Teltonika RMS remote management support
Gigabit Ethernet and Fibre Connectivity The switch provides 24 managed RJ45 Ethernet ports with 10/100/1000 Mbps operation and auto MDI/MDIX crossover. Four additional SFP ports provide fibre connectivity for network uplinks and longer-distance connections, while support for IEEE 802.3i, 802.3u, 802.3ab, 802.3x, 802.3az and 802.3ad standards allows it to integrate into a range of network environments.

PoE+ Power Delivery Twelve Ethernet ports support IEEE 802.3af PoE and IEEE 802.3at PoE+ using Alternative A. Each PoE+ port can provide up to 30 W, with a combined PoE power budget of 300 W. PoE management can be configured on individual ports, making it possible to monitor and control power delivery to connected equipment.

Layer 2 and Layer 3 Networking The SWM280 provides Layer 2 switching functions together with Layer 3 networking capabilities. Features include VLAN segmentation, STP and RSTP, loop protection, static IPv4 and IPv6 routing, DHCPv6 client support and dynamic routing protocols including BGP, OSPF v2, RIP v1/v2 and EIGRP.

Industrial Protocol Support Support for industrial networking protocols makes the switch suitable for applications that require communication between network infrastructure and industrial equipment. The switch supports PROFINET, EtherNet/IP and MRP, with PROFINET Class B conformance available with the applicable order code.

Traffic Management and Security Traffic management features include QoS prioritisation, bandwidth control, rate limiting, storm control, port-based traffic shaping and port mirroring. Network access can be controlled through 802.1X, MAC filtering, VLAN separation and authentication methods including RADIUS and TACACS+.

Remote Management and Diagnostics Network administrators can manage the switch through its WebUI and Teltonika RMS. SNMP v2 and v3, LLDP and Teltonika's Web API provide additional management options, while diagnostic tools include cable diagnostics, ping, traceroute and nslookup. RMS can also be used for firmware and configuration management across multiple devices.

The Teltonika SWM281 is a managed L2+ Gigabit Ethernet switch that provides 24 Gigabit Ethernet ports alongside four dedicated SFP interfaces. It combines Layer 2 switching with Layer 3 routing capabilities, giving network administrators extensive control over VLANs, traffic, routing and connected devices across copper and fibre connections.

Key Features of Teltonika SWM281 24 x Gigabit Ethernet RJ45 ports
4 x SFP ports for fibre connectivity
Managed L2+ switching with Layer 3 functionality
Static IPv4 and IPv6 routing
Dynamic routing with BGP, OSPF v2, RIP v1/v2 and EIGRP
VLAN, STP, RSTP and loop protection
PROFINET, MRP and EtherNet/IP support
SNMP v2 and v3 management
QoS with port, DSCP, 802.1p and TOS priority
Port mirroring and bandwidth control
802.1X port-based network access control
Teltonika RMS remote management support
56 Gbps non-blocking bandwidth
83.33 Mpps forwarding rate
1U rack-mount form factor
Gigabit Ethernet Connectivity The SWM281 provides 24 RJ45 Ethernet ports supporting 10/100/1000 Mbps connections. Auto MDI/MDIX crossover support allows compatible network devices to connect without requiring specific cable types, while four dedicated SFP ports provide additional options for fibre-based network links and uplinks.

Layer 2 and Layer 3 Networking The switch combines managed Layer 2 functions with Layer 3 networking features. VLAN segmentation, STP, RSTP and loop protection help control network traffic, while static IPv4 and IPv6 routing and dynamic protocols such as BGP, OSPF v2, RIP v1/v2 and EIGRP provide additional routing options.

Industrial Protocol Support The SWM281 supports industrial networking protocols including PROFINET, MRP and EtherNet/IP. PROFINET Class B conformance is available with the applicable optional order code, while MRP can operate in both client and manager roles.

Traffic Management Traffic management features include port priority, DSCP priority, 802.1p priority and TOS priority. Scheduling methods include SP, WFQ and WRR, while rate limiting, storm control and port-based traffic shaping provide further control over network traffic.

Network Security Network access can be controlled using 802.1X authentication, MAC filtering and VLAN separation. Authentication options include pre-shared keys, RADIUS and TACACS+, with support for blocking IP addresses and login attempts. Port isolation provides an additional method of separating connected devices.

Management and Diagnostics The switch supports SNMP v2 and v3, LLDP and web-based management, while Teltonika RMS provides remote management capabilities. Diagnostic tools include cable diagnostics, ping, traceroute and nslookup. A package manager and SDK package with a build environment are also available for additional software functionality.

Performance and Installation The SWM281 provides 56 Gbps of non-blocking bandwidth and a forwarding rate of 83.33 Mpps, with a 512 KB packet buffer and an 8K MAC address table. It supports jumbo frames up to 10,000 bytes and uses a 1U rack-mount form factor measuring 483 x 44 x 234 mm.

Power and Construction The switch uses a C14 power connector and accepts 100-240 VAC at 50/60 Hz. Power consumption is specified at 5.5 W when idle and up to 20 W at maximum load. The housing and panels are made from anodized aluminium, with a grounding screw and software reset button included.

The Teltonika SWM282 is a managed PoE+ network switch that provides 24 Gigabit Ethernet ports with power and data delivery alongside 4 SFP ports for fibre connectivity. It combines Layer 2 switching with Layer 3 networking features, supporting VLAN segmentation, dynamic routing, QoS, network security and industrial protocols for managing a wide range of connected equipment.

Key Features of Teltonika SWM282 24 x Gigabit Ethernet ports supporting 10/100/1000 Mbps
24 x PoE+ ports supporting up to 30 W per port
300 W total PoE power budget
4 x SFP ports for fibre connectivity
Managed Layer 2 switching with Layer 3 capabilities
56 Gbps non-blocking bandwidth
83.33 Mpps forwarding rate
Static IPv4 and IPv6 routing
Dynamic routing with BGP, OSPF v2, RIP v1/v2 and EIGRP
VLAN, STP, RSTP and loop protection
PROFINET, MRP and EtherNet/IP support
SNMP v2 and v3 management
QoS with port, DSCP, 802.1p and TOS priority
Teltonika RMS remote management support
1U rack-mount form factor
Gigabit Ethernet and Fibre Connectivity The switch provides 24 RJ45 Ethernet ports supporting 10/100/1000 Mbps connections, with auto MDI/MDIX crossover support for straightforward device connections. Four SFP ports provide additional fibre interfaces for uplinks and network links where longer cable distances or fibre infrastructure are required.

PoE+ Power Delivery All 24 Ethernet ports support IEEE 802.3af PoE and IEEE 802.3at PoE+ using Alternative A. Each port can supply up to 30 W, while the switch provides a total PoE power budget of 300 W. Individual port PoE management allows connected powered devices to be monitored and controlled through the switch interface.

Layer 2 and Layer 3 Networking The SWM282 combines managed Layer 2 switching with Layer 3 networking functions. VLAN, STP, RSTP and loop protection features help organise network traffic, while static IPv4 and IPv6 routing and dynamic protocols including BGP, OSPF v2, RIP v1/v2 and EIGRP provide additional routing capabilities.

Industrial Protocol Support Support for PROFINET, MRP and EtherNet/IP allows the switch to be integrated into industrial networking environments. PROFINET Class B conformance is available with the applicable optional order code, while MRP supports both client and manager roles.

Traffic Management Traffic management features include port, DSCP, 802.1p and TOS priority settings, with SP, WFQ and WRR scheduling methods. Rate limiting, storm control and port-based traffic shaping provide further control over bandwidth and network traffic, while port mirroring can be used for monitoring and diagnostics.

Network Security and Management The switch supports 802.1X port-based network access control, MAC filtering and VLAN separation. Authentication options include pre-shared keys, RADIUS and TACACS+. SNMP v2 and v3, LLDP, WebUI and the Teltonika Networks Web API provide several methods for monitoring and managing the network.

Performance and Diagnostics The SWM282 provides 56 Gbps of non-blocking bandwidth and a forwarding rate of 83.33 Mpps. It includes a 512 KB packet buffer, an 8K MAC address table and jumbo frame support for packets up to 10,000 bytes. Diagnostic tools include cable diagnostics, ping, traceroute and nslookup.

Remote Management Teltonika RMS provides remote management functions for the switch, including firmware and configuration management. The SWM282 is shipped with two years of RMS Management, providing access to remote monitoring and administration features.

Rack-Mount Installation The switch uses a 1U rack-mount format with an anodized aluminium housing and panels. It measures 483 x 44 x 234 mm and weighs 2291 g. The unit accepts 100-240 VAC at 50/60 Hz and has an IP30 rating, with operating temperatures from 0 °C to 50 °C.

The Teltonika TSF000 is a compact unmanaged Ethernet switch built for installations where cabinet space is limited. It provides five 10/100 Mbps Ethernet ports, including four PoE+ ports capable of supplying up to 30 W each, with a combined PoE power budget of 120 W. Its flat aluminium housing, integrated DIN rail bracket and front-facing Ethernet connections allow convenient installation in industrial cabinets, control panels and other confined areas. A 7-57 VDC power input provides flexibility for different industrial power systems, while plug-and-play operation allows connected devices to communicate without switch configuration.

Key Features of Teltonika TSF000 5 x 10/100 Mbps Ethernet RJ45 ports
4 x PoE+ output ports
IEEE 802.3af PoE and IEEE 802.3at PoE+ support
Up to 30 W PoE power per port
120 W total PoE power budget
Unmanaged plug-and-play operation
7-57 VDC power input
Integrated DIN rail mounting bracket
Low-profile 113 x 28 x 50 mm housing
Anodised aluminium housing and panels
9216-byte jumbo frame support
2K MAC address table
IP30 protection rating
Compact Industrial Connectivity The low-profile form factor measures 113 x 28 x 50 mm and weighs 142 g, making the switch suitable for locations where available cabinet depth is restricted. Its integrated DIN rail bracket provides a practical mounting method for industrial control cabinets and equipment panels.

PoE+ Device Power Four of the five Ethernet ports provide PoE+ output using IEEE 802.3af and IEEE 802.3at standards. Each PoE port can provide up to 30 W, with a total available PoE power budget of 120 W for connected equipment such as IP cameras, access points and other compatible network devices.

Flexible DC Power The switch accepts a 7-57 VDC input through its 3-pin industrial DC power connector. PoE output requires an input voltage within the 44–57 VDC range, while the wider input range allows the switch itself to operate with different DC power sources.

Unmanaged Ethernet Operation As an unmanaged switch, the unit provides straightforward plug-and-play networking without requiring software configuration. The five 10/100 Mbps Ethernet ports support automatic MDI/MDIX crossover, while a 2K-entry MAC address table and 9216-byte jumbo frame support provide additional network handling capabilities.

The Teltonika TSF010 is a compact unmanaged Ethernet switch providing five 10/100 Mbps RJ45 ports for connecting multiple network devices in industrial and space-constrained installations. Its flat form factor measures 113 x 28 x 50 mm and weighs 142 g, while the integrated DIN rail bracket allows straightforward mounting inside cabinets and equipment enclosures. A 3-pin industrial power connector accepts 7–57 VDC, giving the switch flexibility across a range of industrial power systems. Plug-and-play operation means the switch can provide network connectivity without requiring configuration.

Key Features of Teltonika TSF010 5 x 10/100 Mbps RJ45 Ethernet ports
Unmanaged plug-and-play operation
Integrated DIN rail mounting bracket
3-pin industrial DC power connector
7-57 VDC input voltage range
Auto MDI/MDIX crossover support
2K-entry MAC address table
9216-byte jumbo frame support
10 Gbps non-blocking bandwidth
IP30 ingress protection
Five-Port Ethernet Connectivity The switch provides five front-facing RJ45 Ethernet ports supporting 10/100 Mbps connections. Auto MDI/MDIX crossover support allows compatible network devices to connect without requiring crossover cables, making installation straightforward across a range of wired network configurations.

Compact Flat Construction With dimensions of 113 x 28 x 50 mm and a weight of 142 g, the switch occupies little space inside cabinets, terminals and other equipment. Its flat construction places the Ethernet ports opposite the integrated DIN rail bracket, helping it fit into installations where available space is restricted.

Flexible Industrial Power A 3-pin industrial DC power socket accepts an input voltage range of 7-57 VDC. The power input also incorporates overvoltage, reverse-polarity and surge protection features, providing additional protection for the switch when installed in industrial electrical environments.

Unmanaged Plug-and-Play Operation The unmanaged configuration allows the switch to provide Ethernet connectivity without software setup or network management configuration. A 2K-entry MAC address table, 9216-byte jumbo frame support and 10 Gbps non-blocking bandwidth provide the switching capacity required for its five Ethernet ports.

The Teltonika TSW030 is an 8-port unmanaged Ethernet switch providing eight 10/100 Mbps RJ45 connections for linking network equipment in industrial and automation environments. Its integrated DIN rail bracket supports straightforward cabinet installation, while the 2-pin industrial DC power socket accepts a wide 7-57 VDC input range. With plug-and-play operation, low power consumption and a compact anodised aluminium housing, the switch provides a practical way to connect multiple Ethernet devices without requiring network configuration.

Key Features of Teltonika TSW030 8 x 10/100 Mbps RJ45 Ethernet ports
Unmanaged plug-and-play operation
Integrated DIN rail mounting bracket
2-pin industrial DC power input
Auto MDI/MDIX crossover support
20 Gbps non-blocking bandwidth
128 KB packet buffer
2K-entry MAC address table
9216-byte jumbo frame support
IP30 ingress protection
Eight-Port Ethernet Connectivity The switch provides eight RJ45 Ethernet ports supporting 10/100 Mbps connections, allowing multiple network devices to communicate over a single local Ethernet installation. Auto MDI/MDIX crossover support simplifies connections by automatically handling straight-through and crossover cable configurations.

Plug-and-Play Operation As an unmanaged switch, the unit provides Ethernet connectivity without requiring software configuration or network management. This makes it suitable for installations where connected equipment simply needs to be linked together through a local wired network.

Industrial Power Input A 2-pin industrial DC power socket accepts 7-57 VDC. The power input includes overvoltage, reverse-polarity and surge protection, while power consumption is rated at 0.5 W when idle and up to 1.5 W at maximum.

Switching Performance The switch provides 20 Gbps of non-blocking bandwidth, a 128 KB packet buffer and a 2K-entry MAC address table. Jumbo frames up to 9216 bytes are supported, providing additional flexibility for Ethernet networks handling larger data frames.

The Teltonika TSW040 is an unmanaged 8-port PoE+ Ethernet switch that combines 10/100 Mbps wired connectivity with power delivery for compatible network equipment. All eight RJ45 ports support PoE-out, providing up to 30 W per port and a total PoE power budget of 240 W. A 2-pin industrial DC power input supports a 7-57 VDC supply range, while PoE output requires 44-57 VDC. Its integrated DIN rail bracket, compact anodised aluminium housing and wide operating temperature range make it suitable for industrial cabinets, automation systems, smart lighting and other installations requiring both network connectivity and device power.

Key Features of Teltonika TSW040 8 x RJ45 Fast Ethernet ports supporting 10/100 Mbps
8 x PoE-out ports
IEEE 802.3af PoE and IEEE 802.3at PoE+ support
Up to 30 W PoE power per port
240 W total PoE power budget
2-pin industrial DC power input
20 Gbps non-blocking bandwidth
128 KB packet buffer
2K-entry MAC address table
9216-byte jumbo frame support
IP30 ingress protection
Eight-Port PoE+ Connectivity The switch provides eight RJ45 Ethernet ports supporting 10/100 Mbps connections, with every port capable of delivering PoE-out. IEEE 802.3af and IEEE 802.3at compliant PSE ports use spare pairs in Mode B to provide both network connectivity and power over compatible Ethernet cabling.

High PoE Power Capacity Each PoE port can provide up to 30 W at the power sourcing equipment, giving the switch a total PoE power budget of 240 W. This allows multiple compatible devices such as wireless access points, IP cameras, lighting equipment and other PoE network devices to receive power directly through their Ethernet connections.

Flexible Industrial Power A 2-pin industrial DC power socket accepts a 7-57 VDC input, while the PoE-out input voltage range is 44–57 VDC. The power input incorporates overvoltage, reverse-polarity and surge protection to help protect the switch during industrial installation.

Switching Performance The unmanaged switch provides 20 Gbps of non-blocking bandwidth, a 128 KB packet buffer and a 2K-entry MAC address table. Support for jumbo frames up to 9216 bytes provides additional flexibility for Ethernet traffic involving larger data frames, while auto MDI/MDIX crossover simplifies network connections.

The Teltonika TSW114 is an unmanaged Gigabit Ethernet switch with five 10/100/1000 Mbps RJ45 ports for connecting multiple network devices over high-speed wired Ethernet. Its plug-and-play operation requires no additional configuration, while the integrated DIN rail bracket and front-facing connections make installation practical inside industrial control cabinets and other space-conscious environments. A 9-30 VDC power input, compact anodised aluminium housing and wide operating temperature range support use across a variety of industrial settings.

Key Features of Teltonika TSW114 5 x Gigabit Ethernet RJ45 ports
10/100/1000 Mbps Ethernet speeds
Unmanaged plug-and-play operation
10 Gbps non-blocking bandwidth
128 KB packet buffer
2K-entry MAC address table
9216-byte jumbo frame support
IEEE 802.3i, 802.3u, 802.3ab, 802.3x and 802.3az support
Integrated DIN rail mounting bracket
IP30 ingress protection
Gigabit Ethernet Connectivity The switch provides five RJ45 Ethernet ports supporting 10/100/1000 Mbps connections, giving connected equipment access to Gigabit network speeds. Auto MDI/MDIX crossover support allows the ports to automatically accommodate different Ethernet cable configurations.

Plug-and-Play Operation As an unmanaged Ethernet switch, the unit can be installed and used without additional configuration. The five ports provide straightforward network connectivity for industrial equipment, computers, controllers and other Ethernet-enabled devices.

High-Speed Switching A 10 Gbps non-blocking bandwidth capacity supports simultaneous traffic across the five Gigabit Ethernet ports. The switch also provides a 128 KB packet buffer, a 2K-entry MAC address table and jumbo frame support for frames up to 9216 bytes.

Flexible Power Options The switch accepts a 9-30 VDC supply through its 2-pin industrial DC power socket. It can also receive passive PoE power through the ETH1 port using 9–30 VDC. This passive PoE input is not compatible with IEEE 802.3af, 802.3at or 802.3bt power sources.

The Teltonika TSW202 is a managed PoE+ Ethernet switch that combines eight Gigabit Ethernet ports with two SFP ports for flexible copper and fibre connectivity. It provides Layer 2 management with additional Layer 3 features, allowing network administrators to control VLANs, port settings, traffic priorities and routing functions. All eight Ethernet ports support PoE+ with up to 30 W per port and a total PoE power budget of 240 W, while support for PROFINET, EtherNet/IP and MRP makes the switch suitable for industrial networking applications.

Key Features of Teltonika TSW202 8 x Gigabit Ethernet RJ45 ports supporting 10/100/1000 Mbps
2 x SFP ports for fibre optic connectivity
Managed Layer 2 switch with additional Layer 3 features
PoE+ support on all 8 Ethernet ports
IEEE 802.3af and IEEE 802.3at PoE standards
Up to 30 W PoE power per port
240 W total PoE power budget
PROFINET, EtherNet/IP and MRP support
VLAN, STP/RSTP and loop protection
SNMP v2 and v3 support
802.1X port-based network access control
Static IPv4 and IPv6 routing
QoS, port mirroring and bandwidth control
20 Gbps non-blocking bandwidth
8K-entry MAC address table
10,000-byte jumbo frame support
Gigabit Ethernet and Fibre Connectivity The switch provides eight 10/100/1000 Mbps RJ45 Ethernet ports alongside two SFP interfaces for fibre optic connections. The combination allows copper-connected equipment and longer-distance fibre links to operate through the same managed switching platform, with support for IEEE 802.3i, 802.3u, 802.3ab, 802.3x and 802.3z standards.

Managed Network Control The switch provides Layer 2 management features including VLAN configuration, STP/RSTP, loop protection, port isolation, port mirroring and link speed control. Additional Layer 3 functionality includes static IPv4 and IPv6 routing, DHCPv6 client support and static IPv6 addressing.

PoE+ Power Distribution All eight Gigabit Ethernet ports provide PoE+ output using IEEE 802.3af and IEEE 802.3at standards. Each port can deliver up to 30 W at the power sourcing equipment, with a total PoE power budget of 240 W. This allows compatible cameras, wireless access points, sensors and other network devices to receive power and data through their Ethernet connections.

Industrial Protocol Support Support for industrial networking protocols includes EtherNet/IP, PROFINET and MRP. The switch also supports SNMP v2 and v3, LLDP and 802.1X port-based network access control, providing additional options for integrating the switch into managed industrial networks.

Traffic Management and Performance QoS features include port priority, DSCP priority, 802.1p priority and TOS, while scheduling methods include SP, WFQ and WRR. Bandwidth controls provide rate limiting and storm control. The switch offers 20 Gbps of non-blocking bandwidth, a 512 KB packet buffer, an 8K-entry MAC address table and jumbo frame support up to 10,000 bytes.

Industrial Installation The anodised aluminium housing measures 132 x 44.2 x 122.2 mm and weighs 610 g. An integrated DIN rail bracket supports cabinet installation, while wall mounting and flat-surface placement are also available with an additional mounting kit. The switch accepts 7-57 VDC, with PoE operation requiring an input voltage of 44 VDC or higher. It operates from -40 °C to 75 °C and has an IP30 ingress protection rating.

The Teltonika TSW210 is an unmanaged industrial Ethernet switch that combines eight Gigabit Ethernet ports with two SFP interfaces for flexible copper and fibre network connections. The eight RJ45 ports support speeds of up to 1000 Mbps, while the SFP ports provide connectivity for longer-distance fibre links. Plug-and-play operation allows connected equipment to communicate without additional configuration, and the 2-pin industrial DC power input supports a wide 7-57 VDC range. An aluminium housing, DIN rail and surface mounting options, and an operating temperature range of -40 °C to 75 °C make the switch suitable for a variety of industrial installations.

Key Features of Teltonika TSW210 8 x Gigabit Ethernet RJ45 ports supporting 10/100/1000 Mbps
2 x SFP ports for long-distance fibre-optic connectivity
Unmanaged plug-and-play operation
20 Gbps non-blocking bandwidth
128 KB packet buffer
2K-entry MAC address table
9216-byte jumbo frame support
Auto MDI/MDIX crossover support
IEEE 802.3i, 802.3u, 802.3ab, 802.3x and 802.3az support
7-57 VDC input voltage range
Gigabit Ethernet Connectivity The switch provides eight RJ45 Ethernet ports supporting 10/100/1000 Mbps connections, allowing multiple network devices to communicate at Gigabit speeds. Auto MDI/MDIX crossover support simplifies cabling by automatically accommodating different Ethernet connection types.

Fibre-Optic Connectivity Two SFP ports provide an additional option for connecting fibre-optic network links. This allows devices located farther apart to be connected through compatible SFP transceivers while retaining high-speed network communication.

Plug-and-Play Operation As an unmanaged switch, the unit provides straightforward network connectivity without requiring additional configuration. Connected equipment can be linked through the Ethernet and SFP ports as soon as the switch is powered and installed.

Switching Performance The switch provides 20 Gbps of non-blocking bandwidth, a 128 KB packet buffer and a 2K-entry MAC address table. Jumbo frames up to 9216 bytes are supported, while IEEE 802.3i, 802.3u, 802.3ab, 802.3x and 802.3az standards provide compatibility with a range of Ethernet networking equipment.

Industrial Power and Installation A 2-pin industrial DC power socket supports a 7-57 VDC input range. The full aluminium housing measures 132 x 44.2 x 95.1 mm and weighs 500 g. An integrated DIN rail bracket is available on the standard order code, with wall and flat-surface mounting also supported using an additional kit.

The Teltonika TSW212 is a managed Ethernet switch that combines eight Gigabit Ethernet ports with two SFP ports for flexible copper and fibre network connectivity. It provides Layer 2 management with additional Layer 3 functions, including static IPv4 and IPv6 routing and DHCPv6 client support. Support for EtherNet/IP, PROFINET and MRP makes it suitable for industrial networking environments, while VLAN, STP/RSTP, QoS, port mirroring and bandwidth control provide detailed control over network traffic.

Key Features of Teltonika TSW212 8 x Gigabit Ethernet ports supporting 10/100/1000 Mbps
2 x SFP ports for fibre network connections
Layer 2 managed switching with additional Layer 3 functions
Static IPv4 and IPv6 routing
DHCPv6 client support
PROFINET, EtherNet/IP and MRP support
VLAN, STP/RSTP and loop protection
SNMP v2 and v3 management
QoS with port, DSCP, 802.1p and TOS priority options
20 Gbps non-blocking bandwidth
8K MAC address table
10,000-byte jumbo frame support
TSWOS based on OpenWrt
RMS remote management support
Managed Network Connectivity The eight Gigabit Ethernet ports for connecting network devices at speeds of up to 1000 Mbps, together with two SFP ports for fibre connections. Auto MDI/MDIX support simplifies Ethernet connections, while the combination of copper and fibre interfaces allows the switch to accommodate different network layouts.

Layer 2 and Layer 3 Functions Network administrators can manage VLANs, STP/RSTP, loop protection, port isolation and port mirroring through the switch. Additional Layer 3 capabilities include static IPv4 routing, static IPv6 routing and DHCPv6 client support, providing greater control over network traffic and connected devices.

Industrial Protocol Support Support for industrial networking protocols including PROFINET, EtherNet/IP and MRP allows the switch to integrate with industrial automation equipment. MRP support can be used for ring network configurations, while PROFINET features support industrial Ethernet applications.

Traffic Management Quality of Service features provide options for prioritising network traffic using port, DSCP, IEEE 802.1p and TOS priorities. Rate limiting, storm control and scheduling methods such as SP, WFQ and WRR provide additional control over how data is handled across the network.

Industrial Installation The switch uses a full aluminium housing and supports DIN rail mounting for convenient installation in industrial cabinets and equipment areas. The 9-57 VDC input range supports a variety of industrial power arrangements, while the compact housing measures 132 x 44.2 x 122 mm.

Remote Management TSWOS provides the operating environment for configuring and managing the switch, with Web UI access for network settings and device administration. RMS support enables remote firmware updates and configuration management for compatible deployments.

The Teltonika TSW304 is a compact unmanaged Gigabit Ethernet switch with four RJ45 ports supporting 10/100/1000 Mbps connections. It provides plug-and-play networking with auto MDI/MDIX support and an 8 Gbps non-blocking bandwidth capacity. The switch can receive power through its 2-pin industrial DC socket or via passive PoE through ETH1, while its integrated DIN rail mounting makes installation convenient in industrial cabinets and other space-constrained locations.

Key Features of Teltonika TSW304 4 x Gigabit Ethernet RJ45 ports
10/100/1000 Mbps Ethernet speeds
Unmanaged plug-and-play operation
8 Gbps non-blocking bandwidth
2K MAC address table
128 KB packet buffer
9216-byte jumbo frame support
Auto MDI/MDIX crossover support
Passive PoE input through ETH1
2-pin industrial DC power socket
Integrated DIN rail mounting
IP30 ingress protection
Gigabit Ethernet Connectivity The four RJ45 Ethernet ports support 10/100/1000 Mbps connections, allowing compatible network equipment to communicate at Gigabit Ethernet speeds. Auto MDI/MDIX crossover support removes the need to manually determine the appropriate cable type when connecting devices.

Plug-and-Play Operation As an unmanaged switch, the TSW304 can provide network connectivity without requiring configuration through a management interface. Connected devices can be added to the network and communicate through the switch without additional setup.

Passive PoE Input The switch supports passive Power over Ethernet input through the ETH1 port, allowing the unit to receive 9-30 VDC over an Ethernet cable. This passive PoE function is for powering the TSW304 itself and is not compatible with IEEE 802.3af, 802.3at or 802.3bt PoE standards.

Network Performance The 8 Gbps of non-blocking bandwidth, a 128 KB packet buffer and support for jumbo frames up to 9216 bytes. Its 2K MAC address table allows the switch to maintain forwarding information for connected network devices.