APC Management Cards

UPS management SmartSlot Card which supports the UPSLink protocol for SMT, SMX and SURTD Smart-UPS.

Includes : RS-232 configuration cable , User Manual

APC USB communications - Enables communications with SMX, SMT, SRT and SURTD Smart-UPS models using historical APC proprietary USB usages.

The APC® Expansion Chassis allows the use of APC management cards with APC UPSs that are not equipped with a card slot but do have an advanced computer interface port. The Expansion Chassis can also be used with UPSs that have a card slot to provide additional management cards as shown below.

• Card slot
• Cable marked UPS for connecting to the computer interface port of the UPS
• Power connector for an optional power adapter
• UPS Monitoring port that duplicates the functions of the UPS’s computer interface port
• Status indicator

Includes: Mounting pads , User Manual

Compatibility

The Expansion Chassis can be used with any APC device equipped with an advanced computer interface port. This includes Smart-UPS® and Symmetra® products, and any other accessories that duplicate the functions of a UPS computer interface port, such as Share-UPS®.

APC Easy UPS On-Line SRV Dry Contact Card/Relay I/O Card

High quality, Double-conversion On-line UPS designed for essential power protection needs even in the most unstable power conditions.

Includes: User manual


Dry Contact inputs User assignable inputs allow other equipment alarms to be monitored through the power system controller

 
ECO Mode Operating mode that by-passes unused electrical components in good power conditions to achieve high operating efficiency without sacrificing protection.

 
Generator compatible Ensures clean, uninterrupted power to protected equipment when generator power is used.

 
High efficiency High efficiency rates that remain stable even at lower operating power levels.

 
Input power factor correction Minimizes installation costs by enabling the use of smaller generators and cabling.

 
Safety-agency approved Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

 
Double conversion on-line topology Guarantees a consistently high level of power quality. Any disturbances on the distribution waveform are regenerated via the zero transfer time AC to DC then DC to AC conversion process. The battery is only used as a back-up source.

 
Pure sine wave output on battery Simulates utility power to provide the highest degree of compatibility for active PFC (power factor corrected) servers and sensitive electronics.

 
Intuitive LCD interface Provides clear and accurate information in multiple languages with the ability to configure the UPS locally with easy to use navigation keys.

 
Management Software Allows you to easily monitor your utility power and manage your UPS.

 
Network manageable Most models provide remote power management options of the UPS over the network. Many do not have NMC embedded.

 
Serial connectivity Provides management of the UPS via a serial port.

 
Intelligent Card Slot Customize UPS capabilities with management cards.

 
LCD graphics display Text and mimic diagrams that display modes of operation, system parameters and alarms.

 
LED Indicators Provide easy-to-read status of the unit and utility power conditions.

 
Intelligent battery management Maximizes battery performance, life, and reliability through intelligent, precision charging.

 
Predictive failure notification Provides early-warning fault analysis ensuring proactive component replacement.

 
Audible alarms Provides notification of changing utility power and UPS power conditions.

 
Automatic self-test Periodic battery self-test ensures early detection of a battery that needs to be replaced.

 
Disconnected battery notification Warns when a battery is not available to provide backup power.

 
Installation: 1. Remove the cover of Intelligent Card Slot on the back of the UPS and retain the screws.

2. Slide the card into the open slot and secure with the screws from step 1.

3. Use one 9-pin cable (not supplied) to connect UPS and equipment to implement the remote monitoring and control.

 
Additional information can be found in the User Guide PDF file

APC USB Wi-Fi Device

Wireless communication accessory supporting the reliability, performance and security requirements of IT infrastructures.






 





Key benefits • Flexible, simple installation replacing the traditional wired network cabling • Efficient maintenance with lesser ethernet cabling plus the costs savings that come with it (cables & labor) • Easy adaptation as the network configuration or the size changes with time. • Save space, time, and costs for installation • Reduced clutter • Flexible setup • Improved rack airflow • Faster device commissioning • Fewer points of physical failure • Fully encrypted data transmission • Safeguards from 3rd party visibility


With the AP9834 being a wireless communication accessory, removing ethernet cords and cabling from the equation increases the maintenance efficiency by giving a clear view of any points of failure. It also requires less space to be allocated for it, as well as less time to set up and maintain. As a wireless acessory, there is also a reduction the total attack surface, ensuring a reliable, secure network.


As your IT infrastructure grows and adapts, the AP9834 allows you to save on future maintenance costs as you can easily update the wireless network to meet new configurations. Money can also be saved due to the reduction in cabling costs and the reduced dependence on switches.




Set up and Installation Setting up a device has never been so easy and can be installed in just three easy steps! 1. Insert the device into an available USB port 2. Enable and configure Wi-Fi via the NMC Web user interface 3.LED will flash green when Wi-Fi has successfully been configured and connected


Full specification and details can be found in the PDF file


Product User Guide can be found in the PDF file


Product Quick Start Guide can be found in the PDF file


Product Brochure can be found in the PDF file

Remote monitoring and control of an individual UPS by connecting it directly to the network.

AP9810 Features

APC Dry Contact I/O Accessory

Customizable Input Contacts - Monitor conditions from external devices.
Customizable Output Relays - Control output from external devices via output relay(s).

APC Easy UPS On-Line SRV SNMP Card

APV9601 NMC card allows for direct connection and control of an individual APC Easy UPS On-Line SRV UPS unit via SNMP. The configurable notification features keep you informed of detected problems as and when they occur.

Includes: CD with software, User manual


10/100 BaseT Connection Connect the device to a network using a 10 or 100 BaseT connection

 
ECO Mode Operating mode that by-passes unused electrical components in good power conditions to achieve high operating efficiency without sacrificing protection.

 
Generator compatible Ensures clean, uninterrupted power to protected equipment when generator power is used.

 
High efficiency High efficiency rates that remain stable even at lower operating power levels.

 
Input power factor correction Minimizes installation costs by enabling the use of smaller generators and cabling.

 
Safety-agency approved Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

 
Double conversion on-line topology Guarantees a consistently high level of power quality. Any disturbances on the distribution waveform are regenerated via the zero transfer time AC to DC then DC to AC conversion process. The battery is only used as a back-up source.

 
Pure sine wave output on battery Simulates utility power to provide the highest degree of compatibility for active PFC (power factor corrected) servers and sensitive electronics.

 
Intuitive LCD interface Provides clear and accurate information in multiple languages with the ability to configure the UPS locally with easy to use navigation keys.

 
Management Software Allows you to easily monitor your utility power and manage your UPS.

 
Network manageable Most models provide remote power management options of the UPS over the network. Many do not have NMC embedded.

 
Serial connectivity Provides management of the UPS via a serial port.

 
Intelligent Card Slot Customize UPS capabilities with management cards.

 
LCD graphics display Text and mimic diagrams that display modes of operation, system parameters and alarms.

 
LED Indicators Provide easy-to-read status of the unit and utility power conditions.

 
Intelligent battery management Maximizes battery performance, life, and reliability through intelligent, precision charging.

 
Predictive failure notification Provides early-warning fault analysis ensuring proactive component replacement.

 
Audible alarms Provides notification of changing utility power and UPS power conditions.

 
Automatic self-test Periodic battery self-test ensures early detection of a battery that needs to be replaced.

 
Disconnected battery notification Warns when a battery is not available to provide backup power.

 
Installation: 1. Remove the cover of Intelligent Card Slot on the back of the UPS and retain the screws.

2. Slide the card into the open slot and secure with the screws from step 1.

3. Connect a network interface cable to the 10/100 Base-T network connector (RJ-45) A on the SNMP Card.

 
Additional information can be found in the User Guide PDF file

APC Easy UPS SMV Network Management Card

Easy UPS provides power protection for unstable power conditions, ensuring consistent and reliable connectivity at the most critical moments.

Includes: CD with software, User manual


Safety-agency approved Ensures the product has been tested and approved to work safely with the connected service provider equipment and within the specified environment.

 
10/100 BaseT Connection Connect the device to a network using a 10 or 100 BaseT connection

 
Intelligent battery management Maximizes battery performance, life, and reliability through intelligent, precision charging.

 
Battery failure notification Provides early-warning fault analysis on batteries enabling timely preventive maintenance.

 
Advanced Safety Features Safeguard your Home UPS from overloads, excessive mains voltages, short circuits, installation mishaps and battery damage due to low voltage situations.

 
Battery backup and surge protection Outlets provide abundant runtime for network gateway equipment and other critical low-power devices, allowing for hours of internet access during a power outage.

 
Battery and surge protected outlets Back up and protect your hardware and data during power outages, surges and spikes.

 
Transformer-block spaced outlets Protect equipment with input transformer blocks without blocking access to other receptacles.

 
Boost Automatic Voltage Regulation (AVR) Preserves battery life and maximizes runtime by correcting low voltages without discharging the battery.

 
Sleek design Slim, modern design can be upright, flat, or wall-mounted to comfortably fit any electronics set-up and complement home décor.

 
Cold-start capable Provides temporary battery power when the utility power is out.

 
LED Indicators Provide easy-to-read status of the unit and utility power conditions.

 
Audible alarms Provides notification of changing utility power and UPS power conditions

 

Product description

The Schneider Electric Dry Contact I/O SmartSlot Card consists of a printed circuit board assembly. It installs in the SmartSlot of the UPS host device. The contents shipped with the product are:
The Dry Contact I/O SmartSlot Card
The USB A to Mini B cable (to access the Configuration Utility, see Connecting to the Configuration Utility)
A Printed User Manual
The Schneider Electric™ Dry Contact I/O SmartSlot Card is a management product that provides the following features:
UPS status information presented through 6 fully isolated output relays. This is expandable to 8 using universal input/output ports and optional Dry Contact I/O Accessory (AP9810)
UPS control and testing by using 4 opto-isolated input contacts. An additional 4 input contacts (non opto-isolated) may be added using universal input/output ports and an optional Dry Contact I/O Accessory (AP9810)
UPS control and testing based on environmental conditions using universal input/output ports and an optional Environmental Sensor (AP9335T or AP9335TH)
Screw terminal connectors for easy integration into various management systems
A Configuration Utility user interface to customize your setup
Product Diagram

Product Detail
Universal I/O Ports 1 and 2 - These support the AP9335T/TH and AP9810 dry contact accessories
USB Cable Connector - Connecting this to your PC enables usage of the configuration utility.
Reset Button - Use an appropriately sized, non-metallic tool to press the Reset button.
LED Status Indicator
Dip Switches - These are located near the back of the front panel on the right-hand side.
Output Relay Terminals - Connections for alarm outputs.
Input Contact Terminals - Connections for control inputs.
Cord Grip - Supports the cabling that is used to control external devices, or to connect up external switches. 

The UPS Interface Expander 2 (AP9624) from APC by Schneider Electric provides two additional computer interface ports for a UPS equipped with a SmartSlot™ accessory slot.

This enables the UPS and your power management software to provide a graceful system shutdown for up to three network servers or other devices during an extended power outage.

The Interface Expander 2 draws power from the UPS in order to monitor the UPS and report power conditions such as on-battery and low battery events whether the UPS is receiving AC utility power or not.

Includes : RS-232 configuration cable , User Manual , Warranty card

Features of the Interface Expander 2

• Mounts in all supported APC by Schneider Electric devices equipped with a SmartSlot accessory slot.
• Works well in a heterogeneous network. Servers running different operating systems can monitor the same UPS simultaneously.
• Typically supports smart signalling on the serial port of the UPS.
• Can delay shutdown of the UPS until all servers have shut down gracefully.
• Has operating modes that cause the UPS to shut down after confirmation from all protected devices or after an interval set by the user. 
• Does not depend on the operation of the network to protect connected devices. As a hard-wired accessory, the Interface Expander 2 reliably conveys important status messages during poor power conditions.

APC UPS Network Management Card 3 (NMC3) allows for secure remote monitoring and control of an individual APC UPS via a web browser, command line interface of SNMP. The configurable notification features keep you informed of problems as they occur.

For protected servers, the included Powerchute™ Network Shutdown software provides graceful, unattended shutdown in the event of a power outage (certified Vmware Ready, Nutanix Ready, Nutanix-AHV Ready).

Product Features

EcoStruxure™ IT Integration

Monitor and manage your equipment more efficiently. The vendor-neutral architecture delivers a new standard for proactive insights on critical assets of an IT environment. Network Management System (NMS) compatible

Make device information available to your preferred NMS by forwarding SNMP traps (events) or polling across SNMP (v1/v2c/v3) using the PowerNet MIB.  
Environmental Monitoring & Modbus support

Enables remote monitoring and interfaces with EcoStruxure IT, building management systems or other third-party systems Reboot Equipment Remotely

Quickly re-establish availability over your network and save dispatching technicians to remote locations.  
Smart Battery Management

Manage and maintain entire battery system with detailed battery information, even battery cartridge parameters, providing early fault warning.


Flash Upgradeable Firmware:

Convenient remote installation of UPS firmware updates. Powerchute Network Shutdown Software

Operating system shutdown with advanced integration support support for VMware® ESX/ESXi & Microsoft® Hyper-V and SCVMM.  
UPS Network Management Card 3 Comparison Features Benefit AP9640 AP9641 AP9643 SNMP Management (v1/v2/v3) Monitor and manage your UPS as one of your network devices over your preferred Enterprise Network Management System by forwarding SNMP traps (events) across SNMP (v1/v2/v3) using the PowerNet MIB. • • • Data Event Logging Identify problematic trends and take appropriate action before they escalate or export logs for analysis • • • IPv6 Support Ready to support the next generation of IP networking with the trending Internet of Things (IoT) and Industrial IoT. • • • Smart Battery Management
(SRT and SRTL SmartUPS Only) Manage and maintain entire battery system with detailed battery information, even battery cartridge parameters, providing early fault warning. Helps you plan preventative battery maintenance. • • • User friendly Firmware Upgrade capability Install maintenance releases off firmware remotely to your NMC or UPS* ensuring ongoing remote management of your UPS. *SMT, SMTL, SMX, SRT, SRTL models* • • • BACnet/IP* and Modbus TCP Support Integrate your UPS to existing networks with 3rd party Building Management System and Industrial Automation Systems • • • Two USB ports Supports UPS NMC firmware upgrade • • • USB Wi-Fi Device Compatible Providing secure wireless internet to your connected devices (UPS and Rack PDUS). Drives operational efficiency, reducing downstream costs and clutter from traditional cabling   • • Temperature and (optional) Temperature & Humidity Monitoring AP9335T - included, AP9335TH - optional Monitor temperature or temperature and humidity and take appropriate action when needed to ensure best possible performance from your UPS   • • Optional Dry Contact I/O Accessory (AP9810) support Monitor external triggers and initiate actions or external devices   • • Additional Protocol Interface (4-wire Modbus RTU) Supports device communication on a Modbus serial line using the RTU. This mode has greater character density.     • Languages (User Interface) support: Simplified, Chinese, English, French, German, Italian, Japanese, Korean, Portuguese, Russian, Spanish

The American Power Conversion (APC)® Triple Chassis is a 3-slot expansion chassis in which you can install APC management cards for the following purposes:

• To use cards with an APC UPS that has no card slot but has an advanced-signaling computer interface port
• To add cards to a UPS that has one or two card slots, but can support more cards
• To use cards, such as the Environmental Monitoring Card, in a stand-alone configuration

Includes: DB9-DB9 cable , Rack Mounting brackets , User Manual

The APC UPS Network Management Card 3 with Environmental Monitoring provides remote monitoring and control of an individual UPS by connecting it directly to the network. The product consists of a temperature sensor, USB cable and user manual
APC UPS Network Management Card 3 (NMC3) allows for secure remote monitoring and control of an individual APC UPS via a web browser, command line interface of SNMP. The configurable notification features keep you informed of problems as they occur.

For protected servers, the included Powerchute™ Network Shutdown software provides graceful, unattended shutdown in the event of a power outage (certified Vmware Ready, Nutanix Ready, Nutanix-AHV Ready).

Product Features

EcoStruxure™ IT Integration

Monitor and manage your equipment more efficiently. The vendor-neutral architecture delivers a new standard for proactive insights on critical assets of an IT environment. Network Management System (NMS) compatible

Make device information available to your preferred NMS by forwarding SNMP traps (events) or polling across SNMP (v1/v2c/v3) using the PowerNet MIB.  
Environmental Monitoring & Modbus support

Enables remote monitoring and interfaces with EcoStruxure IT, building management systems or other third-party systems Reboot Equipment Remotely

Quickly re-establish availability over your network and save dispatching technicians to remote locations.  
Smart Battery Management

Manage and maintain entire battery system with detailed battery information, even battery cartridge parameters, providing early fault warning.


Flash Upgradeable Firmware:

Convenient remote installation of UPS firmware updates. Powerchute Network Shutdown Software

Operating system shutdown with advanced integration support support for VMware® ESX/ESXi & Microsoft® Hyper-V and SCVMM.  
UPS Network Management Card 3 Comparison Features Benefit AP9640 AP9641 AP9643 SNMP Management (v1/v2/v3) Monitor and manage your UPS as one of your network devices over your preferred Enterprise Network Management System by forwarding SNMP traps (events) across SNMP (v1/v2/v3) using the PowerNet MIB. • • • Data Event Logging Identify problematic trends and take appropriate action before they escalate or export logs for analysis • • • IPv6 Support Ready to support the next generation of IP networking with the trending Internet of Things (IoT) and Industrial IoT. • • • Smart Battery Management
(SRT and SRTL SmartUPS Only) Manage and maintain entire battery system with detailed battery information, even battery cartridge parameters, providing early fault warning. Helps you plan preventative battery maintenance. • • • User friendly Firmware Upgrade capability Install maintenance releases off firmware remotely to your NMC or UPS* ensuring ongoing remote management of your UPS. *SMT, SMTL, SMX, SRT, SRTL models* • • • BACnet/IP* and Modbus TCP Support Integrate your UPS to existing networks with 3rd party Building Management System and Industrial Automation Systems • • • Two USB ports Supports UPS NMC firmware upgrade • • • USB Wi-Fi Device Compatible Providing secure wireless internet to your connected devices (UPS and Rack PDUS). Drives operational efficiency, reducing downstream costs and clutter from traditional cabling   • • Temperature and (optional) Temperature & Humidity Monitoring AP9335T - included, AP9335TH - optional Monitor temperature or temperature and humidity and take appropriate action when needed to ensure best possible performance from your UPS   • • Optional Dry Contact I/O Accessory (AP9810) support Monitor external triggers and initiate actions or external devices   • • Additional Protocol Interface (4-wire Modbus RTU) Supports device communication on a Modbus serial line using the RTU. This mode has greater character density.     • Languages (User Interface) support: Simplified, Chinese, English, French, German, Italian, Japanese, Korean, Portuguese, Russian, Spanish

The APC UPS Network Management Card 3 with Environmental Monitoring and Modbus provides remote monitoring and control of an individual UPS by connecting it directly to the network. The product consists of a temperature sensor, USB cable and user manual
APC UPS Network Management Card 3 (NMC3) allows for secure remote monitoring and control of an individual APC UPS via a web browser, command line interface of SNMP. The configurable notification features keep you informed of problems as they occur.

For protected servers, the included Powerchute™ Network Shutdown software provides graceful, unattended shutdown in the event of a power outage (certified Vmware Ready, Nutanix Ready, Nutanix-AHV Ready).

Product Features

EcoStruxure™ IT Integration

Monitor and manage your equipment more efficiently. The vendor-neutral architecture delivers a new standard for proactive insights on critical assets of an IT environment. Network Management System (NMS) compatible

Make device information available to your preferred NMS by forwarding SNMP traps (events) or polling across SNMP (v1/v2c/v3) using the PowerNet MIB.  
Environmental Monitoring & Modbus support

Enables remote monitoring and interfaces with EcoStruxure IT, building management systems or other third-party systems Reboot Equipment Remotely

Quickly re-establish availability over your network and save dispatching technicians to remote locations.  
Smart Battery Management

Manage and maintain entire battery system with detailed battery information, even battery cartridge parameters, providing early fault warning.


Flash Upgradeable Firmware:

Convenient remote installation of UPS firmware updates. Powerchute Network Shutdown Software

Operating system shutdown with advanced integration support support for VMware® ESX/ESXi & Microsoft® Hyper-V and SCVMM.  
UPS Network Management Card 3 Comparison Features Benefit AP9640 AP9641 AP9643 SNMP Management (v1/v2/v3) Monitor and manage your UPS as one of your network devices over your preferred Enterprise Network Management System by forwarding SNMP traps (events) across SNMP (v1/v2/v3) using the PowerNet MIB. • • • Data Event Logging Identify problematic trends and take appropriate action before they escalate or export logs for analysis • • • IPv6 Support Ready to support the next generation of IP networking with the trending Internet of Things (IoT) and Industrial IoT. • • • Smart Battery Management
(SRT and SRTL SmartUPS Only) Manage and maintain entire battery system with detailed battery information, even battery cartridge parameters, providing early fault warning. Helps you plan preventative battery maintenance. • • • User friendly Firmware Upgrade capability Install maintenance releases off firmware remotely to your NMC or UPS* ensuring ongoing remote management of your UPS. *SMT, SMTL, SMX, SRT, SRTL models* • • • BACnet/IP* and Modbus TCP Support Integrate your UPS to existing networks with 3rd party Building Management System and Industrial Automation Systems • • • Two USB ports Supports UPS NMC firmware upgrade • • • USB Wi-Fi Device Compatible Providing secure wireless internet to your connected devices (UPS and Rack PDUS). Drives operational efficiency, reducing downstream costs and clutter from traditional cabling   • • Temperature and (optional) Temperature & Humidity Monitoring AP9335T - included, AP9335TH - optional Monitor temperature or temperature and humidity and take appropriate action when needed to ensure best possible performance from your UPS   • • Optional Dry Contact I/O Accessory (AP9810) support Monitor external triggers and initiate actions or external devices   • • Additional Protocol Interface (4-wire Modbus RTU) Supports device communication on a Modbus serial line using the RTU. This mode has greater character density.     • Languages (User Interface) support: Simplified, Chinese, English, French, German, Italian, Japanese, Korean, Portuguese, Russian, Spanish