Effective protection for entry-level servers and IT equipment
Salicru's SPS 800 Advance RT2 800 VA UPS features line-interactive technology with sine-wave output voltage and convertible tower/rack format, which has a height of only 2U. In addition, its output power factor of 0.9 and compatibility with APFC (active power factor correction) type loads make it the best option for any type of load that requires protection.
In terms of communications, it features an RS-232/USB interface (compatible with HID protocol) and a smart slot that can optionally hold an SNMP card, MODBUS or potential-free contacts; also available are software packages for local or virtual monitoring and management of protected devices.
Other outstanding features include: solutions for applications with long backup (by means of equipment with extra chargers and additional battery modules), swivel mount display and adapters (pedestal and lugs) for placing in tower or rack formats and programmable outputs (critical/non-critical loads) to extend the available backup.
Line-interactive technology with sine-wave output.
Permanent AVR stabilisation.
Output power factor PF=0.9.
Control panel with swivel mount LCD display and keypad.
Convertible tower/rack format (2U).
Includes pedestal (pedestal mount) and lugs (rack mount).
Backup extensions available for all power ratings.
UPS models with extra charger for backup extensions.
Downloadable monitoring software for Windows, Linux and Mac.
Smart slot for SNMP/potential-free contacts/MODBUS.
EPO – emergency power off.
Programmable outputs for critical/non-critical loads.
Manual and automatic battery test.
Smart battery charger to shorten average recharging times.
Battery recharging with device turned off.
SLC Greenergy solution.
Configuration values, fault codes and remaining backup.
Level of battery available.
Level of load connected.
Input values (current, voltage and frequency).
Output and battery values (current, voltage and frequency).
The features of the SPS ADVANCE RT2 series make it a versatile solution for protecting a wide range of IT equipment such as basic servers, routers, switches, hubs and point-of-sale with high power density requirements and/or rack installation of servers/ communications.
Connection for battery module (only in models with extra charger).
ADSL/fax/modem transient protector.
Emergency stop (EPO).
Socket IEC C19 (only for 3000 VA model).
Resettable thermal cutoff (fuse for 800 and 1100 VA models).
Plug (IEC 14 for 800, 1100 and 1500 VA models; IEC 20 for 2000 and 3000 VA models).
Smart slot for SNMP/potential-free contacts/ MODBUS.
Sockets (8 x IEC 13), programmable critical (x4) / non-critical (x4).
SPS 800 ADVANCE RT2
UPS Power (VA / W)
800 / 720
Line-interactive with sine-wave output
Convertible tower/rack (2U)
8 x power IEC 60320 C13
AC outlet type
IEC 60320 C13
208 / 220 / 230 / 240 V
170 - 280 V up to 100% load
50 / 60 Hz ±5%
208 / 220 / 230 / 240 V
Voltage accuracy (battery mode)
Pure sine wave
Total harmonic distortion (THDv)
≤2% linear load;
≤5% non-linear load
< 120% off at 5 min / < 150% off at 10 s
< 120% off at 1 min / < 150% off at 10 s
Yes, for critical / non-critical loads (4/4)
50/60 Hz (same as input)±0.1%
Stabiliser mode (AVR)
Pb-Ca sealed, AGM, maintenance-free
Against power surges, undervoltages and alternating current components
Automatic on every start + one times a week
I/U (constant current/constant voltage)
4 hours to 90%
Smart slot for SNMP / potential-free contacts / MODBUS
Downloadable monitoring software
For Windows, Linux and Mac
Cold start (start-up from batteries)
Emergency power off (EPO)
ADSL/fax/modem transient protector
Yes, automatic stop in battery mode with load <5%
Smart fan speed
Yes, smart control of fan speed
Site wiring fault
Yes, error detection of phase-neutral rotation and/or absence of earth
0ºC - 40ºC
Up to 95%, non-condensing
Noise level at 1 metre
Less 45 dB
Dimensions (D x W x H mm)
410 x 438 x 88 (2U)
Electromagnetic compatibility (EMC)
Quality & Environmental Management
ISO-9001 and ISO-14001