APC Netshelter SX Rack Accessories

Available for additional hardware needs or to accommodate equipment mounted in varying mounting options.

Accessories to aid in the installation of rack mount IT equipment and to secure racks into position within an enclosure.

Includes: (100) #12-24 x 0.5 inch pilot screws

23 in. (584 mm) to 19 in. (482 mm) mounting adapter brackets for use with AR7510 23 in. (584 mm) EIA mounting rails

Accessories to aid in the installation of rack mount IT equipment and to secure racks into position within an enclosure.

Includes: (4) Brackets, Mounting hardware

Occupies 1U of rack space Conserve valuable rack space in the data center.

Installation:

Stabilization plates and hardware to prevent tip over in stand-alone rack applications.

Bolt-down brackets for NetShelter SX enclosures. Meets UBC Zone-4 Seismic anchoring requirements.

Includes: Installation guide, Mounting hardware

Installation:

Available for additional hardware needs or to accommodate equipment mounted in varying mounting options.

Cage nuts with #10-32 thread for mounting equipment in enclosure for square mounting rails. Accommodates devices using #10-32 mounting screws (Qty. 36).

Includes: (36) #10-32 caged nuts

Installation:

Install caged nuts on the back of the mounting rails, opposite the equipment to be mounted.
Insert the caged nut into the mounting hole by hooking one ear of the caged nut through the far side of the hole.
Place the caged nut tool (included) on the other ear of the caged nut and pull forward to snap it into position.
Bullet point four

Accessories to aid in the installation of rack mount IT equipment and to secure racks into position within an enclosure.

Includes: Installation guide, Mounting hardware

Installation:

NetShelter SX stabilization plate to prevent tipping when sliding out equipment

Stabilization plates to prevent tip over in stand-alone rack applications and meet specific anchoring requirements

Includes: Front stabilizing plate, Installation guide, Mounting hardware

Installation:

Accessories to aid in the installation of rack mount IT equipment and to secure racks into position within an enclosure.

Includes: Installation guide, Rack mounting hardware

Four-post rack accessories Mounts on sides as a spacer when using vertical cable managers between two racks
Mounts on face of vertical rails, perpendicular, for single rack applications
Designed to toollessly mount APC rack PDUs
Installation:

Fixed and sliding shelves to enable the mounting of tower units, monitors, and other equipment into the rack environment

Accessories to aid in the installation of rack mount IT equipment and to secure racks into position within an enclosure.

Double-side fixed shelf for two-post rack

Includes: Installation guide, Mounting hardware

Installation:

Intermediate mounting rails for supporting shallow depth equipment

Enables users to mount equipment with different depths in a 48U, 750 mm enclosure.

Installation: The following procedure demonstrates a top mounting flange installation.

Align the four small holes on the 6U mounting rail with four holes on the vertical mounting flange.
Install four cage nuts in the side-facing holes (from Step 1) of the vertical mounting flange. Install an additional two cage nuts in the side-facing holes even with the slots on the 6-U mounting rail.
Install a 6U mounting rail on the vertical mounting flange using four M6 x 12 screws and the cage nuts installed in Step 2.
Repeat Steps 1 through 3 for the opposite side of the cabinet.
The following procedure demonstrates a bottom flange installation. Choose six holes on the 15U mounting rail and align those holes with holes on the vertical mounting flange in the location you selected.
Choose six holes on the 15U mounting rail and align those holes with holes on the vertical mounting flange in the location you selected.
Install a 15U mounting rail on the vertical mounting flange, using four M6 x 12 screws and the cage nuts installed in Step 2.
Repeat Steps 1 through 3 for the opposite side of the cabinet.

Vertical EIA rail mounting kits

Accessories to aid in the installation of rack mount IT equipment and to secure racks into position within an enclosure.

ncludes: Installation guide, Mounting hardware

Installation: 1. Place the 23 in. Electronic Industries Alliance (EIA) vertical mounting rail onto the enclosure side brace.

2. When the EIA vertical mounting rail is in the proper location, slide the locking screw up, until the teeth in the bracket engage fully with the teeth in the side brace.

3. Using the Torx T30/Phillips #2 wrench, tighten the screw.

4. Repeat for all flanges to be replaced within the cabinet.